The Gen 2 Red Series Fan & Light Switch (LZW36) is a discontinued Z-Wave 700 series two-piece kit: a wall switch with dual LED bars plus a canopy module that splits a single fan circuit into separate fan speed and dimmable light control.
Entities in Home Assistant
44 entities via Z-Wave
Primary entities 6 What automations and dashboards use.
| Entity | Type | Device class | Unit |
|---|---|---|---|
| Fan (main) | fan | — | — |
| Light (main) | light | — | — |
| Local protection state | select | — | — |
| RF protection state | select | — | — |
| Electric Consumed [W] | sensor | — | W |
| Electric Consumed [kWh] | sensor | — | kWh |
Configuration 38 Settings exposed as entities, tunable from Home Assistant.
| Entity | Type | Device class | Unit |
|---|---|---|---|
| Reset accumulated values | button | — | — |
| Active Power Reports disabled | number | — | — |
| Auto Off Fan Timer disabled | number | — | — |
| Auto Off Light Timer disabled | number | — | s |
| Default Light Level (Local) disabled | number | — | — |
| Default Light Level (Z-Wave) disabled | number | — | — |
| Energy Reports disabled | number | — | — |
| Fan LED Indicator Color disabled | number | — | — |
| Fan LED Strip Effect Color disabled | number | — | — |
| Fan LED Strip Effect Duration disabled | number | — | — |
| Fan LED Strip Effect Intensity disabled | number | — | — |
| Fan LED Strip Intensity disabled | number | — | — |
| Fan LED Strip Intensity (When OFF) disabled | number | — | — |
| Fan LED Strip Timeout disabled | number | — | s |
| Fan State After Power Restored disabled | number | — | — |
| Light Dimming Speed disabled | number | — | — |
| Light Dimming Speed (From Switch) disabled | number | — | — |
| Light LED Indicator Color disabled | number | — | — |
| Light LED Strip Effect Color disabled | number | — | — |
| Light LED Strip Effect Duration disabled | number | — | — |
| Light LED Strip Effect Intensity disabled | number | — | — |
| Light LED Strip Intensity disabled | number | — | — |
| Light LED Strip Intensity (When OFF) disabled | number | — | — |
| Light LED Strip Timeout disabled | number | — | s |
| Light Ramp Rate disabled | number | — | — |
| Light Ramp Rate (From Switch) disabled | number | — | — |
| Light State After Power Restored disabled | number | — | — |
| Maximum Fan Level disabled | number | — | — |
| Maximum Light Level disabled | number | — | — |
| Minimum Fan Level disabled | number | — | — |
| Minimum Light Level disabled | number | — | — |
| Periodic Power & Energy Reports disabled | number | — | — |
| Default Fan Level (Local) disabled | select | — | — |
| Default Fan Level (Z-Wave) disabled | select | — | — |
| Fan LED Strip Effect disabled | select | — | — |
| Instant On disabled | select | — | — |
| Light LED Strip Effect disabled | select | — | — |
| Local Protection disabled | select | — | — |
Verified against Home Assistant 2026.8.3: its own Z-Wave discovery
run over core's node dump of this device
(LZW36)
.
Most of these are configuration parameters, which Home Assistant creates
disabled and you enable as needed.
Events and automation triggers
Presses on this device reach Home Assistant as device triggers through
the
Z-Wave
integration, which you pick in the automation editor after pairing.
The button list, and whether each button also becomes an
event
entity, comes from what the device reports at pairing time, so it
appears once the device is on the network.
Read from Home Assistant 2026.8.3: the integration declares these trigger types, and core holds no per-model button list for this device.
Recipes using this device
Recipes that can use it
These recipes are built around other hardware, and pick this device up as an optional extra.
Motion Hallway Light
Installs a Home Assistant automation that turns a hallway or landing light on when motion is seen and off again once the space has been still for a grace period you set. Add a light sensor and it only runs after dark, add a presence sensor and it holds the light while someone lingers.
Movie Mode
Installs a Home Assistant automation that dims the lights when the TV starts playing and brings them back when it stops. Add shades to close, a soundbar to power on, a scene button to trigger it by hand, and dimmable accent lights.
Presence Room Lighting
Installs a Home Assistant automation that keeps a room's lights on for as long as an mmWave presence sensor sees someone in it, and switches them off shortly after the room empties. Add a light sensor to run only after dark, and dimmable lights that come up softly.